Home
Ec-SimEE CALCULATORS
Interactive Circuit Design & Direct SPICE Export

Sallen-Key 2nd-Order Filter — Sallen-Key Low-Pass

Toggle between Unity-Gain Sallen-Key Low-Pass and High-Pass topologies. Solve for R1, R2, C1, C2, or natural corner frequency fc = 1 / (2π√(R1·R2·C1·C2)).

18 • ACTIVE FILTERS

Interactive Sallen-Key 2nd-Order Filter Solver

Type values into any fields (using standard engineering suffixes like m, u, n, k, M) and leave the remaining field empty to solve for it.

Circuit Parameters

Ω
Ω
F
F
Solve Target
Hz
Interactive Schematic Preview — Click any reference badge to focus its input field
R1 10 kΩR2 10 kΩC1 20 nFC2 10 nFGBW 1 THzfc 1.125 kHz
Natural Frequency (fc)
1.125 kHz
1 / (2π√(R1·R2·C1·C2))
Quality Factor (Q) & ζ
Q = 0.7071 (ζ = 0.707)
Butterworth (Maximally Flat)
Capacitor Ratio (C1 / C2)
2.00 : 1
For R1 = R2 Butterworth, set C1 = 2·C2
Op-Amp GBW (1 THz)
−40 dB/decade
GBW / fc = 888576588× margin
Op-Amp Gain-Bandwidth Product (GBW)GBW
Default 1T (1 THz) simulates an ideal op-amp. We recommend setting GBW from your device's datasheet for an accurate high-frequency Bode plot:
Hz
Nearest Standard EIA Resistor Values
Snap calculated resistances to standard 5% (E24) or 1% (E96) commercial values:
FREQUENCY RESPONSE

Bode Plot (Amplitude & Phase)

Interactive dual-axis AC frequency response (1 Hz to 100 MHz). Move or drag your mouse across the plot to inspect amplitude and phase.

Hz
Hz
dB
dB
f = 10 kHz● Amp: -37.95 dB● Phase: -170.8°
1 Hz10 Hz100 Hz1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz0 dB+180°-15 dB+90°-30 dB0°-45 dB-90°-60 dB-180°
FORMULAS & THEORY

Sallen-Key 2nd-Order Filter Equations & Design Guidelines

Core transfer equation: fc = 1 / (2π · √(R1 · R2 · C1 · C2))

1. 1. Sallen-Key 2nd-Order Synthesis

Introduced by R. P. Sallen and E. L. Key at MIT Lincoln Lab in 1955, the unity-gain Sallen-Key topology synthesizes 2nd-order complex poles without inductors:

  • Natural Frequency (fc): fc = 1 / (2π × √(R1 × R2 × C1 × C2))
  • Quality Factor (LPF): Q = √(R1 × R2 × C1 × C2) / [C2 × (R1 + R2)]

2. 2. Equal-Resistor Butterworth Recipe

Setting R1 = R2 = R simplifies the Q equation to Q = 0.5 × √(C1 / C2):

  • Butterworth (Q = 0.7071): Choose C1 = 2 × C2 with R1 = R2
  • Bessel (Q = 0.5774): Choose C1 = 1.333 × C2 with R1 = R2
WORKED EXAMPLE & PRACTICE

Using the Sallen-Key 2nd-Order Filter Calculator in a Real Design

The Sallen-Key stage makes a second-order filter from one op-amp, two resistors and two capacitors. With equal resistors, the ratio of the capacitors sets the Q: a ratio of two gives the maximally flat Butterworth response. It is the standard building block for anti-aliasing and reconstruction filters.

Worked example: A 1 kHz Butterworth-like low-pass

R1 = R2 = 10 kΩ, C1 = 22 nF (feedback) and C2 = 10 nF (to ground).

  1. fc = 1 / (2π × 10 kΩ × √(22 nF × 10 nF)) = 1 / (2π × 10 kΩ × 14.8 nF) = 1073 Hz.
  2. Q = ½ √(C1/C2) = ½ √2.2 = 0.74, close to the Butterworth value of 0.707.

What it means: A corner near 1.07 kHz, rolling off at 40 dB per decade with almost no peaking. Standard values put the Q 5% above Butterworth, a peak of about 0.1 dB.

Common mistakes

  • High-frequency feedthrough. Far above the corner the signal passes through C1 into the op-amp’s output, whose impedance is no longer low. The stopband attenuation bottoms out and then gets worse. Follow the stage with a passive RC if that matters.
  • Capacitor tolerance sets the Q. The Q depends on the capacitor ratio. Two 10% capacitors can move it from 0.74 to anywhere between 0.67 and 0.82. Use 5% or better C0G or film parts.
  • Op-amp bandwidth. As a rule the GBW should be at least 100 × fc × Q for the response to follow the design.