Home
Ec-SimEE CALCULATORS
Interactive Circuit Design & Direct SPICE Export

RC Time Constant & Charge — Charging: Vc = Vs(1 − e^(−t/τ))

Toggle between Capacitor Charging and Discharging modes. Solve for Vc(t), elapsed time t, resistance R, capacitance C, or supply voltage Vs.

06 • TRANSIENTS & PASSIVES

Interactive RC Time Constant & Charge Solver

Type values into any fields (using standard engineering suffixes like m, u, n, k, M) and leave the remaining field empty to solve for it.

Circuit Parameters

V
Ω
F
s
Solve Target
V
Interactive Schematic Preview — Click any reference badge to focus its input field
Vs 5 VR1 10 kΩC1 100 nFt 1 msVc(t) 3.161 V
Time Constant (τ = R·C)
1 ms
5τ Settling (99.3%) = 5 ms
Stored Energy & Peak I0
1.25 µJ
Ipeak = Vs/R = 500 µA
10%–90% Rise Time (tr)
2.197 ms
tr = ln(9)·τ ≈ 2.2·RC
Equivalent −3 dB Cutoff
159.2 Hz
t / τ = 1.00 time constants
Nearest Standard EIA Resistor Values
Snap calculated resistances to standard 5% (E24) or 1% (E96) commercial values:
FREQUENCY RESPONSE

Bode Plot (Amplitude & Phase)

Interactive dual-axis AC frequency response (1 Hz to 100 MHz). Move or drag your mouse across the plot to inspect amplitude and phase.

Hz
Hz
dB
dB
f = 10 kHz● Amp: -35.96 dB● Phase: -89.1°
1 Hz10 Hz100 Hz1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz0 dB+180°-15 dB+90°-30 dB0°-45 dB-90°-60 dB-180°
FORMULAS & THEORY

RC Time Constant & Charge Equations & Design Guidelines

Core transfer equation: τ = R·C • Vc(t) = Vs·(1 − e^(−t/RC))

1. 1. Exponential RC Charging & Discharging

A series RC network governed by a first-order differential equation responds exponentially with time constant τ = R × C:

  • Charging Equation: Vc(t) = Vs × (1 − e^(−t / RC))
  • Discharging Equation: Vc(t) = Vs × e^(−t / RC)
  • Solve for Elapsed Time t: t = −R × C × ln(1 − Vc / Vs)

2. 2. Key RC Milestones

At each multiple of τ = RC, the capacitor reaches a fixed percentage of its final asymptote:

  • 1τ = 63.2% • 2.2τ = 10%–90% Rise Time: 3τ = 95.0% • 5τ = 99.3% (fully settled)
  • Stored Electrostatic Energy: E = ½ × C × Vs² (Joules)
WORKED EXAMPLE & PRACTICE

Using the RC Time Constant & Charge Calculator in a Real Design

A capacitor charging through a resistor follows an exponential whose time scale is τ = R·C. The calculation sets power-on reset delays, debounce times and soft-start ramps, and tells you how long a node needs to settle to a given accuracy.

Worked example: A reset delay on a 3.3 V rail

A 100 kΩ resistor charges 1 µF from 3.3 V. What is the voltage after 100 ms?

  1. τ = 100 kΩ × 1 µF = 100 ms, so 100 ms is exactly one time constant.
  2. Vc = 3.3 V × (1 − e⁻¹) = 3.3 V × 0.632 = 2.09 V.

What it means: After one time constant the capacitor is at 63% of the supply. A logic input with a 2.0 V threshold would switch at about that moment; settling to within 1% takes 4.6 τ, here 460 ms.

Common mistakes

  • Using it as a precise timer. Capacitor tolerance, the temperature coefficient of the dielectric and the spread of the logic threshold together easily make ±30%. For a defined delay use a supervisor IC or a timer.
  • Slow edges into logic. A slowly rising RC waveform spends a long time near the threshold, where an ordinary gate can oscillate. Use an input with hysteresis.
  • Discharge path at power-down. If the supply collapses quickly, the capacitor stays charged unless a diode across the resistor lets it follow. A brief power dip then produces no reset at all.