Home
Ec-SimEE CALCULATORS
Interactive Circuit Design & Direct SPICE Export

BJT Voltage-Divider Bias (Class-A Amplifier) Calculator

Solve for quiescent collector-emitter voltage Vce, supply Vcc, base divider resistors R1, R2, collector resistor Rc, or emitter resistor Re in a Class-A BJT stage.

24 • TRANSISTORS

Interactive BJT Amplifier Bias Solver

Type values into any fields (using standard engineering suffixes like m, u, n, k, M) and leave the remaining field empty to solve for it.

Circuit Parameters

V
Ω
Ω
Ω
Ω
Solve Target
V
Interactive Schematic Preview — Click any reference badge to focus its input field
Vcc 12 VR1 47 kΩR2 10 kΩRc 4.7 kΩVce 5.877 VRe 1.4 kΩ
Quiescent Collector Current (Icq)
1.004 mA
Vb = 2.11 V • Ve = 1.41 V
Transistor Power (PQ = Vce·Ic)
5.899 mW
Vc = 7.28 V
Transconductance (gm = Ic/VT)
38.83 mS
re' = 25.85mV / Ic = 25.75 Ω
Degenerated Voltage Gain (|Av|)
3.30 V/V (10.36 dB)
Rc / (Re + re′)
Nearest Standard EIA Resistor Values
Snap calculated resistances to standard 5% (E24) or 1% (E96) commercial values:
FREQUENCY RESPONSE

Bode Plot (Amplitude & Phase)

Interactive dual-axis AC frequency response (1 Hz to 100 MHz). Move or drag your mouse across the plot to inspect amplitude and phase.

Hz
Hz
dB
dB
f = 10 kHz● Amp: 10.36 dB● Phase: 179.7°
1 Hz10 Hz100 Hz1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz20 dB+180°5 dB+90°-10 dB0°-25 dB-90°-40 dB-180°
FORMULAS & THEORY

BJT Amplifier Bias Equations & Design Guidelines

Core transfer equation: Vb ≈ Vcc·R2/(R1+R2) • Ic ≈ (Vb − 0.7)/Re • Vce = Vcc − Ic·(Rc+Re)

1. 1. Emitter-Degenerated Bias Stability

Fixing base voltage Vb via R1 and R2 while placing Re in the emitter makes quiescent current Ic = (Vb − Vbe)/Re nearly independent of transistor β variations:

  • Stiff Divider Rule of Thumb: Choose R1 ∥ R2 ≤ 0.1 × β × Re so base current does not load the divider.
  • Maximum Symmetrical Swing: Center Vce ≈ Vcc / 2 for maximum undistorted AC output swing.

2. 2. Small-Signal Gain & Bypass Capacitor

Without an emitter bypass capacitor, voltage gain is tightly controlled by the external resistor ratio −Rc / Re.

  • Unbypassed Gain: Av = −Rc / (Re + re′) where re′ = VT / Ic ≈ 26 mV / Ic
WORKED EXAMPLE & PRACTICE

Using the BJT Amplifier Bias Calculator in a Real Design

A four-resistor bias network fixes a transistor’s operating point so that it depends on resistor ratios and hardly at all on the transistor’s gain, which varies three to one between parts. The emitter resistor is the key: it applies negative feedback that holds the collector current steady.

Worked example: Biasing a 12 V common-emitter stage at about 1 mA

Vcc = 12 V, R1 = 47 kΩ, R2 = 10 kΩ, Rc = 4.7 kΩ and Re = 1.4 kΩ.

  1. Base voltage: Vb ≈ 12 V × 10 kΩ / 57 kΩ = 2.11 V.
  2. Emitter voltage = 2.11 V − 0.7 V = 1.41 V, so Ic ≈ 1.41 V / 1.4 kΩ = 1.0 mA.
  3. Vce = 12 V − 1.0 mA × (4.7 kΩ + 1.4 kΩ) = 5.9 V.

What it means: The transistor sits at 5.9 V and 1 mA, near the middle of its range, leaving room for the collector to swing about 4.5 V either way.

Common mistakes

  • A divider that is too weak. The base current loads the divider. Make the divider current at least ten times the base current, otherwise Vb, and with it the operating point, depends on gain after all.
  • Too little voltage on the emitter. The stabilising effect comes from the emitter voltage being large compared with the variation in Vbe. Aim for at least 1 V across Re; a tenth of the supply is a common rule.
  • Re reduces the gain. Unbypassed, the stage gain is only about Rc/Re, 3.4 here. Bypass Re with a capacitor to recover the full gain for AC signals.